FEATURED EQUIPMENT

Ford 600 Classic Tractor

$4,495.00
Gas Engine 
Electric Start
6 Volt Electrical System
Manual Transmission
3 Point Hitch 
540 PTO
Manual Transmission
Manual Steering
Two Wheel Drive
Front Work Lights
Rear Draw Bar
 
Brand New Battery
 
 
Showing 1004 Hours
 
C/w Massey Ferguson Spring Tine Dual Row 3 Point Hitch Cultivator
 
Starts And Runs Excellent
 
$4,495.00
The Ford 600 Series tractors began production in 1954, and continued until 1957. Quite similar to the Ford NAA (Golden Jubilee) in design, it used the same 132 cubic inch Red Tiger engine with 31 horsepower. Several different models were made in the 600 Series, and these numbers were used to denote whether they used a particular transmission, hydraulic system, or PTO. The result was five different model numbers: 620, 630, 640, 650 and 660.These break down as follows:
Model 620: Four-speed transmission, no PTO or three-point hitch
Model 630: Four-speed transmission without PTO
Model 640: Four-speed transmission with PTO and with three-point hitch
Model 650: Five-speed transmission, non-live PTO with three-point hitch
Model 660: Five-speed transmission, live PTO and three-point hitch
All of these tractor carry the “Ford 600” series badge on the radiator.Considered a two-plow utility tractor, this one proved to be very popular with the farmer. Note: the picture shown above is actually of a Ford 671 model. Very similar in appearance.

$113.61/month OAC

 

Financing Available

2008 Montana 5740C Cab Tractor

$32,995.00
****SUPER LOW HOURS 452****
57 Horsepower Liquid Cooled Diesel Engine
Dual Rear SCV
Loader Joystick
Cab
Heater
Air Conditioning
Mechanical Front Wheel Drive
Power Steering
Front And Rear Work lights
Exterior Mirrors
Tilt Steering
Front Windshield Wiper
8 Speed Reverser Transmission
Block Heater
Glow Plugs
 
C/w TMG RT1175 Rototiller
 
Tractor Has Recent Engine Oil And Filter, Hydraulic Filter And Outer Air Filter Replaced. New Camso Front Tires

$758.49/month OAC

 

Financing Available

2018 Sky Jack SJ1056TH Telehandler

$109,995.00
ONLY 4274 Hours
10,000 Pound Lift Capacity
56 Foot Reach
Cab 
Heater
Defroster Fan
Auxiliary Hydraulics
****SWIVEL FORK CARRIAGE****
48 Inch Tines
Wide Fork Carriage
Foam Filled Tires
Back Up Alarm
Positive Air Shut Off
Hydraulic Out Riggers
 
Nice Clean Machine

$2,474.91/month OAC

■ 10,000 lbs (4,535 kg) Maximum lift capacity
■ 56’ 3” (17.14 m) Maximum lift height
■ 4,000 lbs (1,814 kg) Capacity @ maximum lift height (no outriggers)
■ 6,000 lbs (2,722 kg) Capacity @ maximum lift height (on outriggers)
■ 42’6” (12.95 m) Maximum forward reach
■ 400 lbs (181 kg) Capacity @ maximum forward reach (no outriggers)
■ 3,000 lbs (1,361 kg) Capacity @ maximum forward reach (on outriggers)
■ DPF & DEF Free Tier 4 final 74hp/287 lb-ft Deutz TCD 3.6L engine
■ 20,000 lbs Drawbar pull
■ 3 Speed Dana powershift transmission & Dana axles
■ Yoke mounted lifting hook
■ 48” Quick attach, floating pin carriage
■ Pallet forks, 2.36”x4”x48”, 10,000 lbs capacity
■ Axle mount outriggers
■ Auxiliary hydraulics
■ Engine block heater
■ Quick attach carriage mount
■ Rear window with wiper
■ Side window
■ Suspension seat
■ Single multifunction pilot operated joystick control
■ In cab engine multifunction display
■ Hydraulic test ports
■ Lockable in cab storage box
■ Rear towing hitch pin
■ Fiberglass engine cowling
■ Steel component and access covers

 

Financing Available

FEATURED ATTACHMENTS

Pallet Fork Frame And Single Arm Grapple

$2,995.00
Heavy Duty 5,500 Pound Rated Main Frame
60 Inch Long Tines
4,000 Pound Rated Tines
Single Arm Hydraulic Quick Attach Grapple
C/w Hoses And Flat Face Couplers
Made With Canadian Steel
 
Hydraulic Arm Lifts Straight Up So Forks Can Be Used As Normal When Hydraulic Grapple Arm Is Not Needed
 
Super Handy Attachment For Clean Up And Demolition Jobs
$75.70/month OAC

Financing Available

TMG SB84 Inch Rock Rake

$1,595.00
Features
Built to handle jobs in demolition, recycling, scrap yards, forestry, agriculture, landscaping, construction and more
84” of working width allows you to work with varying load sizes and awkward debris piles that need the loose material separated
4” skeleton tine spacing allows you to sift larger rocks from piles of dirt, gravel and other mixed aggregate that needs partitioning
Serrated cutting edges will dig into the ground with the force of your skid steer to reach under the earth or heavy piles to process large loads
Made from solid steel and has a tare weight of over 420 lb; no mechanical or moving parts so there will be little to no maintenance over the years
Compatible with 45-70 HP medium frame skid steers; dependable attachment that can be used for a variety of purposes and stores easily when not in use
Universal mount that will fit most skid steers, turning it into a multi-use, versatile jobsite asset that is strong and reliable
$42.94/month OAC

Financing Available

Unused AGT Industrial 72 Inch Skid Steer Powered Rock Rake

$4,495.00
Picks up material as small as 3/4″. Adjustable side skids for setting depths.
Top cover opens hydraulically for easier dumping.
Exclusive replaceable bolt-on rake bars.
Rake bars scarify and level while breaking up lumpy soil and picking up rocks.
Dual springs on cover allow for adjustable down-pressure.
 
Universal Skid Steer Quick Attach Plate
 
Weld On Cutting Edge
$113.61/month OAC
Model
ECSSLR72
Working Width
72″
Number Of Racks
12
Bucket Capacity(m³）
0.4
Total Number Of Teeth
456
Flow (L/min)
60-120
Working Pressure (MPa)
14-20
Weight
1929.04 lbs
Measurement
83” × 66” × 42”

Financing Available

Sign Up for Hot Deals

REGISTER